A New Technique for Broadband Matching of Open-Ended Rectangular Waveguide Radiator.

The maximum reflection at an open end of a standard rectangular waveguide is about -10 dB in its operating frequency range. It is often used without matching. For critical applications, it is desirable to further reduce the reflection coefficient. In this paper, a new technique is presented for the broadband impedance matching of an open-ended rectangular waveguide. The proposed technique employs three thin capacitive matching elements placed at proper intervals via a low-loss dielectric material. The capacitance of, and distance between, the matching elements are optimized for broadband impedance matching using a simulation tool. Based on the proposed technique, two design examples are presented for the matching of a WR75 waveguide radiator. A reflection coefficient of less than -16 dB and -20 dB has been achieved over a ratio bandwidth of 2.13:1 and 1.62:1, respectively.

Two-Stage Model-Based Predicting PV Generation with the Conjugation of IoT Sensor Data.

This paper proposes a novel short-term photovoltaic voltage (PV) prediction scheme using IoT sensor data with the two-stage neural network model. It is efficient to use environmental data provided by the meteorological agency to predict future PV generation. However, such environmental data represent the average value of the wide area, and there is a limitation in detecting environmental changes in the specific area where the solar panel is installed. In order to solve such issues, it is essential to establish IoT sensor data to detect environmental changes in the specific area. However, most conventional research focuses only on the efficiency of IoT sensor data without taking into account the timing of data acquisition from the sensors. In real-world scenarios, IoT sensor data is not available precisely when needed for predictions. Therefore, it is necessary to predict the IoT data first and then use it to forecast PV generation. In this paper, we propose a two-stage model to achieve high-accuracy prediction results. In the first stage, we use predicted environmental data to access IoT sensor data in the desired future time point. In the second stage, the predicted IoT sensors and environmental data are used to predict PV generation. Here, we determine the appropriate prediction scheme at each stage by analyzing the model characteristics to increase prediction accuracy. In addition, we show that the proposed prediction scheme could increase prediction accuracy by more than 12% compared to the baseline scheme that only uses a meteorological agency to predict PV generation.

Observer-based state estimation for discrete-time semi-Markovian jump neural networks with round-robin protocol against cyber attacks.

This paper investigates an observer-based state estimation issue for discrete-time semi-Markovian jump neural networks with Round-Robin protocol and cyber attacks. In order to avoid the network congestion and save the communication resources, the Round-Robin protocol is used to schedule the data transmissions over the networks. Specifically, the cyber attacks are modeled as a set of random variables satisfying the Bernoulli distribution. On the basis of the Lyapunov functional and the discrete Wirtinger-based inequality technique, some sufficient conditions are established to guarantee the dissipativity performance and mean square exponential stability of the argument system. In order to compute the estimator gain parameters, a linear matrix inequality approach is utilized. Finally, two illustrative examples are provided to demonstrate the effectiveness of the proposed state estimation algorithm.

A Sustainable Business Model for a Neutral Host Supporting 5G and beyond (5GB) Ultra-Dense Networks: Challenges, Directions, and Architecture.

With the deployment of the fifth generation (5G) mobile network systems and the envisioned heterogeneous ultra-dense networks (UDNs), both small cell (SmC) and distributed antenna system (DAS) technologies are required by mobile network operators (MNOs) and venue owners to support multiple spectrum bands, multiple radio access technologies (RATs), multiple optical central offices (COs), and multiple MNOs. As a result, the neutral host business model representing a third party responsible for managing the network enterprise on behalf of multiple MNOs has emerged as a potential solution, mainly influenced by the desire to provide a high user experience without significantly increasing the total cost of ownership (TCO). However, designing a sustainable business model for a neutral host is a nontrivial task, especially when considered in the context of 5G and beyond (5GB) UDNs. In this paper, under an integrated optical wireless network infrastructure, we review how SmC and DAS technologies are evolving towards the adoption of the neutral host business model and identify key challenges and requirements for 5GB support. Thus, we explore recent candidate advancements in heterogeneous network integration technologies for the realization of an efficient 5GB neutral host business model design capable of accommodating both SmC and DAS. Furthermore, we propose a novel design architecture that relies on virtual radio access network (vRAN) to enable real-time dynamic resource allocation and radio over Ethernet (RoE) for flexible and reconfigurable fronthaul. The results from our simulations using MATLAB over two real-life deployment scenarios validate the feasibility of utilizing switched RoE considering end-to-end delay requirements of 5GB under different switching schemes, as long as the queuing delay is kept to a minimum. Finally, the results show that incorporating RoE and vRAN technologies into the neutral host design results in substantial TCO reduction by about 81% in an indoor scenario and 73% in an outdoor scenario.

Design of a Ku-Band Monopulse Antenna with a Truncated Reflector and an Open-Ended Waveguide Feed.

This paper presents a design for a monopulse reflector antenna with asymmetric beamwidths for radar applications at the Ku band. The proposed design features a rectangular waveguide monopulse feed and a truncated parabolic reflector. An array of four open-ended rectangular waveguides were employed to realize a compact monopulse feed. The reflector is cut in the H plane of the feed producing a wider beam in the azimuth plane. This type of pattern is useful in applications such as projectile tracking and airport surveillance. The design parameters for optimum performances are chosen at all stages of the design. The design and analysis have been carried out using the commercial simulation tool CST Studio Suite 2022. The directivity of the sum, elevation difference and azimuth difference channels of the reflector antenna are 32.1, 28.1, and 26.4 dB at 14 GHz; 30.9, 29, and 27.3 dB at 15 GHz; 31.7, 29.6, and 27.6 dB at 16 GHz; 31.6, 29.9, and 27.8 dB at 17 GHz.

Procedure via cross-Kerr nonlinearities for encoding single logical qubit information onto four-photon decoherence-free states.

We propose a photonic procedure using cross-Kerr nonlinearities (XKNLs) to encode single logical qubit information onto four-photon decoherence-free states. In quantum information processing, a decoherence-free subspace can secure quantum information against collective decoherence. Therefore, we design a procedure employing nonlinear optical gates, which are composed of XKNLs, quantum bus beams, and photon-number-resolving measurements with linear optical devices, to conserve quantum information by encoding quantum information onto four-photon decoherence-free states (single logical qubit information). Based on our analysis in quantifying the affection (photon loss and dephasing) of the decoherence effect, we demonstrate the experimental condition to acquire the reliable procedure of single logical qubit information having the robustness against the decoherence effect.

Optical Fredkin gate assisted by quantum dot within optical cavity under vacuum noise and sideband leakage.

We propose a deterministic Fredkin gate which can accomplish controlled-swap operation between three-qubit states. The proposed Fredkin gate consists of a photonic system (single photon) and quantum dots (QDs) confined in single-sided cavities (two electron spin states). In our scheme, the control qubit is the polarization state of the single photon, and two electron spin states in QDs play the role of target qubits (swapped states by control qubit). The interaction between a photon and an electron of QD within the cavity (QD-cavity system) significantly affects the performance of Fredkin gate. Thus, through the analysis of the QD-cavity system under vacuum noise and sideband leakage, we demonstrate that reliable interaction and performance of the QD-cavity system with photonic state (photon) can be acquired in our scheme. Consequently, the Fredkin gate proposed in this paper can be experimentally implemented with high feasibility and efficiency.

Photonic scheme of discrete quantum Fourier transform for quantum algorithms via quantum dots.

We propose an optical scheme of discrete quantum Fourier transform (DQFT) via ancillary systems using quantum dots (QDs) confined in single-sided cavities (QD-cavity systems). In our DQFT scheme, the main component is a controlled-rotation k (CRk) gate, which utilizes the interactions between photons and QDs, consisting of two QD-cavity systems. Since the proposed CRk gate can be experimentally implemented with high efficiency and reliable performance, the scalability of multi-qubit DQFT scheme can also be realized through the simple composition of the proposed CRk gates via the QD-cavity systems. Subsequently, in order to demonstrate the performance of the CRk gate, we analyze the interaction between a photon and a QD-cavity system, and then indicate the condition to be efficient CRk gate with feasibility under vacuum noise and sideband leakage.

Scheme for generation of three-photon entangled W state assisted by cross-Kerr nonlinearity and quantum dot.

We represent an optical scheme using cross-Kerr nonlinearities (XKNLs) and quantum dot (QD) within a single-sided optical cavity (QD-cavity system) to generate three-photon entangled W state containing entanglement against loss of one photon of them. To generate W state (three-photon) with robust entanglement against loss of one photon, we utilize effects of optical nonlinearities in XKNLs (as quantum controlled operations) and QD-cavity system (as a parity operation) with linearly optical devices. In our scheme, the nonlinear (XKNL) gate consists of weak XKNLs, quantum bus beams, and photon-number-resolving measurement to realize controlled-unitary gate between two photons while another nonlinear (QD) gate employs interactions of photons and an electron of QD confined within a single-sided optical cavity for implementation of parity gate. Subsequently, for the efficiency and experimental feasibility of our scheme generating W state, we analyze the immunity of the controlled-unitary gate using XKNLs against decoherence effect and reliable performance of parity gate using QD-cavity system.

Capacitance-Voltage Characteristics Analysis of Indium Zinc Oxide Thin Film Transistors Based Ultraviolet Light Irradiation.

The mechanism of solution-processed indium zinc oxide (IZO) thin film transistors (TFTs) made by simultaneous spin coating and ultraviolet (UV) light irradiation was investigated by capacitance-voltage (C-V) measurement. The application of UV light on the IZO TFTs was found to improve the thin film surface structure, and pledge to receive low degree of roughness. Meanwhile, electrical characteristics indicated that the TFT prepared at the UV light irradiation with 90 s exhibits the best performance with field-effect mobility 5.6 cm²/Vs, threshold voltage ═ -0.13 V, subthreshold gate swing 0.64 V/decade and on/off ratio ═ 1.7 × 106. In the C-V contrastive analysis with different UV light irradiation time by 60 s and 90 s, the frequency was varied from 100 Hz to 10 kHz to investigate low as well as high frequency C-V.

Implementation of SWAP test for two unknown states in photons via cross-Kerr nonlinearities under decoherence effect.

We present an optical scheme for a SWAP test (controlled swap operation) that can determine whether the difference between two unknown states (photons) using cross-Kerr nonlinearities (XKNLs). The SWAP test, based on quantum fingerprinting, has been widely applied to various quantum information processing (QIP) schemes. Thus, for a reliable QIP scheme, it is important to implement a scheme for a SWAP test that is experimentally feasible. Here, we utilize linearly and nonlinearly optical (XKNLs) gates to design a scheme for a SWAP test. We also analyze the efficiency and the performance of nonlinearly optical gates in our scheme under the decoherence effect and exhibit a technique employing quantum bus beams and photon-number-resolving measurements to reduce the effect of photon loss and dephasing caused by the decoherence effect. Consequently, our scheme, which is designed using linearly optical devices and XKNLs (nonlinear optics), can feasibly operate the nearly deterministic SWAP test with high efficiency, in practice.

Connectivity Analysis of Cognitive Radio Ad-Hoc Networks with Multi-Pair Primary Networks.

In this paper, we study the connectivity of cognitive radio ad-hoc networks (CRAHNs) where primary users (PUs) and secondary users (SUs) are randomly distributed in a given area following a homogeneous Poisson process. Moreover, for the sake of more realistic CRAHNs, contrary to previous works in the literature, we consider the case that primary network is comprised of multiple communication pairs which are spatial-temporal distributed in the network area. We also take into consideration the differences in transmission range and interference range of both PUs and SUs. The connectivity of such CRAHN is studied from three viewpoints. First, we mathematically analyze the probability of isolated secondary transmitter and secondary receiver. Second, we derive the approximation expression of the link probability between two adjacent SUs. Third, we investigate the path connectivity between two arbitrary SUs by using the simulation analysis approach. The correctness of our mathematical expressions is confirmed by comparing analytical results with simulation results. The results in this paper provide insights into how multiple communication pairs in primary network affect the connectivity of secondary network, which can be useful guidelines for the design of CRAHNs.

Improvement of the Electrical Properties of a Cu(In,Ga)Se2 Solar Cell Based on a ZnS Buffer Layer from Radio Frequency Magnetron Sputtering.

We fabricated zinc sulfide (ZnS) buffer layers with a great band gap and small light loss at a short wavelength, and then applied them to copper indium gallium sulphur-selenide (CIGS) thin film solar cells. A CIGS evaporation system was used for fabrication of the CIGS thin films, and a thickness monitor was used to check the evaporation rate at each source. The evaporation rate and deposition time were adjusted to change the composition ratio of the thin films. Also, CIGS thin films were deposited by changing the temperature of the substrates from room temperature (RT) to 150 °C, 250 °C, and 350 °C during ZnS deposition, and among them, the optimal substrate temperature was selected to measure the light conversion efficiency of ZnS-deposited CIGS thin film solar cells. The grown ZnS thin films were analyzed for crystallinity and composition by using X-ray diffraction, and by using a scanning electron microscope, the cross section and surface shape of the thin films were examined. When we applied the ZnS thin film that was fabricated at a temperature of 150 °C with a thickness of 50 nm as a buffer layer for the CIGS solar cells, we obtained a light conversion efficiency of 14.48% without an antireflection layer.

High-Efficiency Cu(In,Ga)Se2 Thin Film Solar Cells Using ZnS and CdS Buffer Layers.

Most of the existing copper indium gallium diselenide (CIGS) thin film solar cells are based on a cadmium sulfide (CdS) buffer layer fabricated using a chemical bath deposition (CBD) process. However, due to environmental pollution caused by material toxicity and the unique wet process's incompatibility with the vacuum process, many studies are now being actively carried out on nontoxic buffer layers. In this study, to replace CdS buffer layers, zinc sulfide (ZnS) buffer layers with a big band gap and a low optical loss at a short wavelength were fabricated using a magnetron sputtering system. For comparative analysis, this study also fabricated CdS buffer layers using the CBD process. Then, the conversion efficiency of CIGS thin film solar cells deposited with ZnS and CdS thin film as buffer layers was measured. The light conversion efficiency of ZnS buffer layer-based CIGS was measured at 14.44%, while that of the CdS buffer layer-based CIGS was measured at 15.71%. Given that both are higher than the minimum conversion efficiency required for commercialization (10%), ZnS buffer layer-based solar cells could have a competitive edge over the existing CdS buffer layer-based solar cells.

Preparation of quantum information encoded on three-photon decoherence-free states via cross-Kerr nonlinearities.

We present a scheme to encode quantum information (single logical qubit information) into three-photon decoherence-free states, which can conserve quantum information from collective decoherence, via nonlinearly optical gates (using cross-Kerr nonlinearities: XKNLs) and linearly optical devices. For the preparation of the decoherence-free state, the nonlinearly optical gates (multi-photon gates) consist of weak XKNLs, quantum bus (qubus) beams, and photon-number-resolving (PNR) measurement. Then, by using a linearly optical device, quantum information can be encoded on three-photon decoherence-free state prepared. Subsequently, by our analysis, we show that the nonlinearly optical gates using XKNLs, qubus beams, and PNR measurement are robust against the decoherence effect (photon loss and dephasing) in optical fibers. Consequently, our scheme can be experimentally implemented to efficiently generate three-photon decoherence-free state encoded quantum information, in practice.

Performance Evaluation of Relay Selection Schemes in Beacon-Assisted Dual-Hop Cognitive Radio Wireless Sensor Networks under Impact of Hardware Noises.

To solve the problem of energy constraints and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive the exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

Implementation of controlled quantum teleportation with an arbitrator for secure quantum channels via quantum dots inside optical cavities.

We propose a controlled quantum teleportation scheme to teleport an unknown state based on the interactions between flying photons and quantum dots (QDs) confined within single- and double-sided cavities. In our scheme, users (Alice and Bob) can teleport the unknown state through a secure entanglement channel under the control and distribution of an arbitrator (Trent). For construction of the entanglement channel, Trent utilizes the interactions between two photons and the QD-cavity system, which consists of a charged QD (negatively charged exciton) inside a single-sided cavity. Subsequently, Alice can teleport the unknown state of the electron spin in a QD inside a double-sided cavity to Bob's electron spin in a QD inside a single-sided cavity assisted by the channel information from Trent. Furthermore, our scheme using QD-cavity systems is feasible with high fidelity, and can be experimentally realized with current technologies.

Distribution of hybrid entanglement and hyperentanglement with time-bin for secure quantum channel under noise via weak cross-Kerr nonlinearity.

We design schemes to generate and distribute hybrid entanglement and hyperentanglement correlated with degrees of freedom (polarization and time-bin) via weak cross-Kerr nonlinearities (XKNLs) and linear optical devices (including time-bin encoders). In our scheme, the multi-photon gates (which consist of XKNLs, quantum bus [qubus] beams, and photon-number-resolving [PNR] measurement) with time-bin encoders can generate hyperentanglement or hybrid entanglement. And we can also purify the entangled state (polarization) of two photons using only linear optical devices and time-bin encoders under a noisy (bit-flip) channel. Subsequently, through local operations (using a multi-photon gate via XKNLs) and classical communications, it is possible to generate a four-qubit hybrid entangled state (polarization and time-bin). Finally, we discuss how the multi-photon gate using XKNLs, qubus beams, and PNR measurement can be reliably performed under the decoherence effect.

Impact of Beamforming on the Path Connectivity in Cognitive Radio Ad Hoc Networks.

This paper investigates the impact of using directional antennas and beamforming schemes on the connectivity of cognitive radio ad hoc networks (CRAHNs). Specifically, considering that secondary users use two kinds of directional antennas, i.e., uniform linear array (ULA) and uniform circular array (UCA) antennas, and two different beamforming schemes, i.e., randomized beamforming and center-directed to communicate with each other, we study the connectivity of all combination pairs of directional antennas and beamforming schemes and compare their performances to those of omnidirectional antennas. The results obtained in this paper show that, compared with omnidirectional transmission, beamforming transmission only benefits the connectivity when the density of secondary user is moderate. Moreover, the combination of UCA and randomized beamforming scheme gives the highest path connectivity in all evaluating scenarios. Finally, the number of antenna elements and degree of path loss greatly affect path connectivity in CRAHNs.